All-in-one touchscreen displays with Android.

Knowledge and advice

Refresh rate and response time: what do Hz and ms mean for digital signage?

What are refresh rate and response time, and when do you need 60 Hz or 120 Hz for digital signage? Clear explanation for installers with practical advice.

Refresh rate is the number of times per second a display shows a new image, expressed in hertz (Hz). Response time is the time one pixel needs to change colour, expressed in milliseconds (ms). For digital signage, both specs matter: too low a refresh rate causes motion blur with moving images, too high a response time leads to ghosting. In most narrowcasting applications, 60 Hz with a GtG response time under 8 ms is sufficient — but as soon as you show video with rapid movement, different requirements apply.

Refresh rate: what 60 Hz and 120 Hz mean in practice

A 60 Hz display refreshes the image 60 times per second — so each frame is visible for 16,7 ms. A 120 Hz display does this 120 times, halving the visible frame persistence to 8,3 ms. That sounds technical, but the effect is visible: at 120 Hz, motion blur with fast-moving images is around 50 % less than at 60 Hz.

For static content — a menu, an opening-hours slide, a welcome message — you will not notice the difference. However, if you show a live sports feed, a scrolling product carousel or a video wall with rapid cuts, 120 Hz is noticeably smoother for the passer-by.

Rule of thumb: choose 60 Hz for informational or text-based content; choose 120 Hz or higher when you play continuous video with fast motion or when the screen is at eye level in an environment where viewers stay for a long time.

Response time: GtG versus MPRT

On a spec sheet you will see two different response time values, which manufacturers do not always clearly distinguish. GtG (grey-to-grey) measures how quickly one pixel changes from one shade of grey to another — the most common transition in realistic images. MPRT (Moving Picture Response Time) measures how long a moving image remains visible on the retina, and is directly linked to the refresh rate: a 60 Hz display has an MPRT of about 16,7 ms, a 120 Hz display about 8,3 ms.

GtG determines ghosting (trailing shadows behind moving objects); MPRT determines motion blur (blurry edges). For signage installations, GtG is the most useful spec to compare. A GtG value below 5 ms is a good threshold for applications with moving images.

Note: manufacturers sometimes advertise a low MPRT while the GtG value is higher. A display with 1 ms MPRT and 8 ms GtG performs worse during rapid colour changes than the headline spec suggests.

There is no standard that prescribes a minimum Hz value for digital signage. However, ISO 9241-303 sets generic, technology-independent requirements for the image quality of electronic displays — a useful framework for comparing spec sheets, but it does not replace your own assessment of the content the customer plays. So always compare the measurement method behind a figure, not just the figure itself.

When it really matters for signage

Most digital signage content consists of slides, images and short videos with moderate movement speed. For that, 60 Hz with a GtG response time of 6–8 ms is more than sufficient. However, there are three situations where you need higher specifications:

  • Live video or sports content on a large screen (≥ 55") at close viewing distance: choose 120 Hz.
  • Touchscreen kiosks where users quickly scroll or make swipe gestures: a low GtG (< 5 ms) prevents the interface from feeling 'sticky'.
  • LED video walls those that are photographed or filmed (trade fairs, events): a higher internal refresh rate of the LED panel (≥ 960 Hz) prevents the 'water ripple' effect in camera footage — this is a different spec from the 60/120 Hz of the signal frame.

The PixioDisplay Outdoor is available in 49″ and 55″ with a brightness of 3.500 cd/m² and is built for continuous outdoor use — an application in which both thermal load and image quality in bright sunlight place higher demands on the panel than a standard office screen.

The difference between signage displays and consumer TVs

Consumer TVs typically run at 60 Hz or 120 Hz and are designed for use of a few hours per day. Commercial signage displays are built for 16–24 hours of continuous use and have more stable thermal properties, which also keeps the response time stable as they warm up.

A consumer TV with around 300 nits is not designed for continuous use in signage environments. The same applies to the response time specifications: on consumer TVs these are measured under ideal conditions, not at operating temperature after eight hours of running.

For a digital advertising screen in a shop or hospitality setting, a commercial display with guaranteed continuous operation is the right choice — even if the Hz figures look the same on paper.

How to choose the right spec as an installer

Start with the question: what is the customer playing, and how quickly does that content move? Then use this scheme:

Content type Recommended refresh rate Recommended GtG
Static slides, text, images 60 Hz ≤ 8 ms
Video with moderate motion (promotional film) 60 Hz ≤ 6 ms
Fast video, live sport, scrolling feeds 120 Hz ≤ 5 ms
Touchscreen kiosk with swipe interaction 60–120 Hz ≤ 5 ms
LED video wall (camera-proof) 60 Hz signal + ≥ 960 Hz panel refresh n/a

Also check the media player for every project: a player that runs at a maximum of 60 fps gains no benefit from a 120 Hz display. In large installations, that chain matters more than the panel: on Summit more than 50 PixioDisplays were used at one event, and then the source — player, network and encoding — just as often determines image smoothness as the Hz value on the spec sheet. Read more about the choice between SoC and external players in Media players for digital signage: SoC or external player?

Conclusion

For most narrowcasting installations, 60 Hz with a GtG response time under 8 ms is the right choice — this covers informative content, video and simple animations. Choose 120 Hz as soon as the customer wants live video, fast scrolling content or an interactive kiosk. Always check the GtG value on the spec sheet, not just the MPRT headline. And use commercial displays only for continuous use: the response time specifications of consumer TVs are not valid after hours of uninterrupted use.

Want to know more about other image quality parameters? Then read Brightness and contrast in digital signage: nits, standards and settings for the next step in your display specification.

Frequently asked questions

Does a digital signage display need 120 Hz?

Not always. For static content, text slides and promotional videos with gentle motion, 60 Hz is sufficient. Choose 120 Hz when you show live sport, fast scrolling feeds or interactive touchscreen applications — then the smoother image is visible to passers-by.

What is the difference between GtG and MPRT in response time?

GtG (grey-to-grey) measures how quickly a pixel changes colour and determines ghosting. MPRT (Moving Picture Response Time) measures how long a moving image remains visible and is linked to the refresh rate. For signage comparisons, GtG is the most useful value — check that on the spec sheet, not just the MPRT headline.

Can I use a consumer TV as a digital signage display?

That is not recommended. Consumer TVs are not designed for continuous use of 16–24 hours per day. The response time and brightness specifications are measured under ideal conditions, not at operating temperature after hours of uninterrupted use. Commercial displays offer more stable performance and a longer warranty.

What does the high refresh rate (960 Hz+) of LED video walls mean?

With LED panels, the internal refresh rate (960 Hz, 1920 Hz or higher) refers to how quickly the panel itself drives the LEDs. A higher value prevents the 'water ripple' effect when visitors photograph or film the screen. This is a different specification from the 60/120 Hz of the video signal you are driving.

Does the media player affect the refresh rate?

Yes. A media player that outputs a maximum of 60 fps gives no advantage on a 120 Hz display. Always check whether the player and the display support the same maximum frame rate, and whether the connection (HDMI 2.0 or higher, or DisplayPort) offers sufficient bandwidth for higher refresh rates at the desired resolution.

Read also

The full price list

Request the price list brochure

The brochure brings all displays together, with the available purchase, rental and lease prices, versions and options. You will receive the price list by email.

Prefer a different step right away?

We use your data to provide the price list and follow up on your enquiry. You do not need to sign up for updates for this.

We will process your request and follow up by email. A Pixio specialist responds within one working day.